Search found 141 matches

by BB Dyson
Fri Feb 18, 2022 2:14 pm
Forum: Dyson Cordless & Handhelds
Topic: Dyson 7 animal - brush head not spinning
Replies: 1
Views: 703

Re: Dyson 7 animal - brush head not spinning

Hello, the photos are not loading. However what I would say to check; is remove the brush bar from the cleaner head. Near the end there will be a black shield that turns. This contains a big bearing, the normal cause for the motor not spinning when the brush is in, is because this bearing is faulty ...
by BB Dyson
Thu Dec 23, 2021 5:35 pm
Forum: Dyson Cordless & Handhelds
Topic: Dyson Fluffy Purple velvet has worn off
Replies: 3
Views: 2341

Re: Dyson Fluffy Purple velvet has worn off

We are actually getting some of these made, as like you say Dyson do provide them. Also you want to establish if is worn, or covered in a type of 'grime' (often caused by the oil from a pet mixing with dust). If it is spray some polish on there and leave it a little while before wiping off.
by BB Dyson
Thu Dec 23, 2021 5:30 pm
Forum: Dyson DC05, DC08, DC11, DC19, DC20, DC21, DC22, DC23, DC32
Topic: DC05 filter problems
Replies: 3
Views: 3489

Re: DC05 filter problems

If all seals are in place then there should be no reason for an increased amount of fluff going to the filter. Did you notice this problem after cleaning the filter?
by BB Dyson
Sun Jul 18, 2021 11:02 pm
Forum: Dyson DC03
Topic: DC03 Diagram
Replies: 0
Views: 1579

DC03 Diagram

Motor Assy
Image
Main Body
Image
Cyclone & Wand

Image
by BB Dyson
Fri Jul 16, 2021 12:59 am
Forum: Dyson Cordless & Handhelds
Topic: DC35 bin flap
Replies: 2
Views: 7018

Re: DC35

The best way is sometimes to add a little polish to each lug. Place one lug in first and then push the other side in. It can be done and ones you have done it once you will have no issue doing it again :)
by BB Dyson
Thu Jul 15, 2021 11:05 pm
Forum: Dyson DC36, DC38, DC39, DC47, DC54
Topic: DC41C cutting out
Replies: 1
Views: 2010

Re: DC41C

The motor TOC is cutting in for some reason, on some older models they became sensitive over time, so they would stop the motor even if it was running at the correct temperature. If the motor was burnt out you would not be able to keep turning it on, not only that but there would be a terrible burni...
by BB Dyson
Sun Jul 11, 2021 2:10 am
Forum: Dyson DC36, DC38, DC39, DC47, DC54
Topic: Dyson CY23 Vaccuum Head wheels jamming
Replies: 1
Views: 1662

Re: Dyson CY23 Vaccuum Head wheels jamming

Yes it is possible to remove the wheels, it does require force. Big thick screwdrivers either side at the back of the wheel normally does the trick ;)
by BB Dyson
Sun Jul 11, 2021 1:04 am
Forum: Dyson Cordless & Handhelds
Topic: DC44 Animal battery
Replies: 1
Views: 1162

Re: DC44 Animal battery

Unfortunately this would now be classed as 'scrap'. Batteries cannot be swapped with other models. Both models have different motors, so chances are you have blown some components on the PCB.
by BB Dyson
Sun Jul 11, 2021 12:49 am
Forum: Dyson DC04
Topic: Second DC04 belt worn through in ten days
Replies: 5
Views: 9001

Re: Second DC04 belt worn through in ten days

When changing the belt it is always best to make sure that the brush bar spins freely. Also check for any wobbles the brush may have, as this can cause the belt to snap. Sometimes over time, where the belt attaches to the brush it can get warped, causing the belt not to run true, so again check this...
by BB Dyson
Sun Jul 11, 2021 12:20 am
Forum: General Dyson discussion
Topic: DC49 - parts list
Replies: 1
Views: 4213

Re: DC49 - parts list

Cyclone:
Image

Main Body:
Image

Head & Hose:
Image